Pumpernickel

Parts

Contents

To assemble the pcb the following parts are needed:
[table caption=”resistors
– (all 0207, 1% metalfilm)” width=”200″ colwidth=”50|150″ colalign=”left|left”]
quantity | type
1x|51R
4x|100R
1x|150R
3x|300R
1x|820R
1x|1k4 (or 1k5)
1x|1k6
1x|2k2
2x|5k1
3x|10k
1x|15k
3x|20k
1x|27k
1x|28k7 (or 28k)
3x|30k1
1x|40k2
1x|47k

1x|100k
1x|220k
1x|300k
1x|590k
1x|2M
2x|2M2
[/table]

[table caption=”capacitors” width=”400″ colwidth=”50|350″ colalign=”left|left”]
quantity | type
1x|22p (spacing 2.5mm, ceramic-disc)
2x|47p (SMD 1206, NP0)
2x|10n (spacing 5.0mm, film)
1x|22n (spacing 2.5mm, ceramic-disc)

1x|47n (spacing 5.0mm, film)
2x|0.1u (spacing 5.0mm, film)
1x|0.33u (spacing 5.0mm, film)
1x|4.7u (max-Ø:5.0mm, electrolytic)
4x|10u (max-Ø:5.0mm, electrolytic)
1x|22u (max-Ø:7.0mm, electrolytic)
1x|47u (max-Ø:7.0mm, electrolytic)
2x|100u (max-Ø:7.0mm, electrolytic)
1x|220u (max-Ø:8.5mm, electrolytic)
[/table]

[table caption=”semiconductors” width=”700″ colwidth=”50|200|450″ colalign=”left|left”]
quantity | type
8x|3mm LEDs (different colors; like: 5x green, 1x yellow, 2x red)|forward voltage drop of each led must be < 2,3V! The seven leds of the led-bar-graph are wired in series. Therefore the sum of the forward voltage drop must be under 17V!
1x|1N4004
4x|1N4148
1x|THAT4301P20 (DIL20)
1x|LM4558/RC4558 (DIL8)
1x|NE5532 (DIL8)
2x|LM339 (DIL14)
1x|2N2907 (TO92)
1x|78L05 (TO92)
1x|7660S (DIL8)
[/table]

[table caption=”mechanical” width=”600″ colwidth=”50|350|200″ colalign=”left|left”]
Anzahl| Typ
1x|dc-jack print
1x|DPDT-toggle-switch
1x|SPDT-toggle-switch
1x|16/17mm pot angled print 10kB (lin)
2x|16/17mm pot angled print 50k (lin)
1x|16/17mm pot angled print 50kA (log)
1x|trimmer pot 50k (lin)

1x|shaft for trimmer
1x|footswitch (small, min. 1xSPDT)

1x|washer
1x| ≥Ver.: 1.2.0: FRT5 DC5V, Takamisawa A-5W-K or Zettler AZ850-5 |<Ver.:1.2.0: TQ2SA-L-5V
2x|NMJ4HCD2 mono jack
4x|knobs (max-Ø: 19mm, better: 15mm)
2x|DIL16 socket
1x|DIL16 socket

1x|3pin 2.54mm strip

1x|2pin 2.54mm strip

1x|3pin 2.54mm receptacle connector |got to be compatible with the 3pin strip!

1x|2pin 2.54mm receptacle connector |got to be compatible with the 2pin strip!
1x|enclosure: 1590N1 or 125B
[/table]

others: